Description
HIGH-POWER WELDING AND A BROAD RANGE OF APPLICATIONS
40% DUTY CYCLE
Four minutes out of 10 of continuous welding at maximum output power, in other words, one minute more of productive output compared with the average in this power range.
167 CHARACTERISTICS*
/ Steel, CrNi, AlMg, AlSi, Metal Cored, Rutil FCW, Basic FCW, Self-shielded
/ 0.8 – 1.6mm wire diameter
/ Eight different gas mixtures
READY TO WELD IN THREE STEPS
The intuitive operating concept enables welders to start work straight away – no prior knowledge of the device is required.
All the essential welding parameters can be viewed and adjusted on the front panel. The only parameters that have to be selected before welding begins are the gas, wire diameter and material thickness.
70% LESS REWORK, 30% FASTER WELDING
The Pulse function of the TransSteel 4000 and TransSteel 5000 Pulse permits faster welding speeds on thicker materials.
The pulsed arc also reduces the amount of rework, as less welding spatter is generated.
PULSE WELDING – CONTROLLED AND FAST
The new TransSteel 4000 Pulse and TransSteel 5000 Pulse mark the arrival of the pulsed arc in the TransSteel series.
Controlled welding in the intermediate arc range together with optimum weldability when working with aluminum are now part of the basic package.
SPECIAL 4-STEP MODE – A MORE STABLE ARC
The “Special 4-step mode” is particularly suitable for welding in the higher power range. In special 4-step mode, welding starts at a lower power, which makes the arc easier to stabilise.
SYNCHROPULSE
SEAM RIPPLING FOR ALUMINUM ALLOYS
The “SynchroPulse” option is recommended for the welding of aluminum alloys when a rippled seam appearance is required. This effect is achieved by modifying the welding power between two operating points.
! SynchroPulse works in Standard Synergic and Pulse Synergic mode – but only on the TransSteel 4000 and 5000 Pulse.
SPOT AND STITCH WELDING
WITH NO MATERIAL DISTORTION
Spot mode enables you to place welding spots at regular intervals. As you have complete flexibility over the pause time between the intervals, spot welding is ideal for the tacking of workpieces.
Stitch welding not only produces a rippled seam appearance, the low level of heat input reduces any possible material distortion when working with light gage sheets.
Technical specification
Package Contains:
- TransSteel 5000 PULSE Power Source
- FK5000 Cooling Unit
- VR5000 4R/G/FSC Wire Feed Unit with Control Panel
- Watercooled Interconnection Set 5m
- TU 4 Car Pro – 4 Wheel Trolley with Gas Cylinder Holder
- MTW 500i /FSC/UD/3,5m/45°/LED MIG Torch & Universal Liner Kit Fitted
- Set of 4×1.2mm Feed Rolls (Suitable for Steel & Aluminium)
- Earth Lead 4m
| Welding current max. | 400 / 500 A |
| Welding current min. | 10 A |
| Welding current / Duty cycle [10min/40°C] | 500A / 40% |
| Welding current / Duty cycle [10min/40°C] | 420A / 60% |
| Welding current / Duty cycle [10min/40°C] | 360A / 100% |
| Operating voltage | 14,5-39,5V |
| Open-circuit voltage | 65 V |
| Mains frequency | 50-60Hz |
| Mains voltage | 3 x 380V / 400V / 460V |
| Mains fuse | 35A |
| Dimension / b | 300 mm |
| Dimension / l | 747 mm |
| Weight | 32,5 kg |
| Degree of protection | IP23 |
STEEL
TRANSFER TECHNOLOGY
- STEEL is the universal characteristic for quick and easy welding applications.
- STEEL ROOT is the characteristic specifically developed for root pass welding. It is characterised by particularly strong gap-bridging ability, in other words, the ability to fill wide gaps.
- STEEL DYNAMIC is a characteristic with a particularly hard and concentrated arc, resulting in high welding speeds and deep penetration.
- PCS (Pulse Controlled Spray Arc) characteristics* facilitate a combination of intermediate and spray arcs – the result is deep penetration with minimal spattering.
